After all I came to my solution, which may not be 100% original, but
working.
Inspecting many pics and comparing to my "original" setup I have found at
least 3 different solutions on BN4 hardtops alone. And the seal set I
recived from AH4H (Bill Boulton sourced) is yet another type.
???
Make it work, and call it a day.
Gergo
2011/8/7 <warthodson@aol.com>
> I assume you are referring to a roadster hardtop & not a convertible
> hardtop.
> Attached is a drawing of the seals between the rear shroud & the aluminum
> extrusion on the rear of the hardtop. This drawing is for a BN6 & BN7 only.
> In
> theory, the hardtop sits on or is supported by the thick neoprene pads.
> These
> pads do not extend all the way around the rear of the hard top. There are
> two
> pads & they are only Approximately 6" -8" long and are located near the two
> hardtop locating pins. On BN6 & BN7 hardtops there is an inside & an
> outside
> weather seal (as shown on the attached drawing) that extends all the way
> around the back of the hardtop & is visible from both the inside & outside.
> They fill the gap between the shroud & the aluminum hardtop extrusion, but
> are
> not intended to support the weight of the top. The BN4, BT7 hardtop is
> similar, except instead a separate inside & outside seal they only have one
> seal which is "U" shaped. I believe the outside flap of the "U" is longer
> than
> the inside flap of the "U". I also believe that the flaps are visible on
> the
> outside & inside of the BN4 & BT7.Also, the parts book does provide some
> clarity to this.
> Trying to describe this has convinced me that I would not make it as a
> technical writer.
> Yes, I know the drawing was stripped from the list.
> Gary Hodson
>
>
>
>
>
>
>
> -----Original Message-----
> From: Bryan Treen <btreen@telus.net>
> To: healeys <healeys@autox.team.net>
> Sent: Sun, Aug 7, 2011 1:46 pm
> Subject: [Healeys] Factory Hardtop
>
>
> Hi:
> Like Gergo, I too am a bit unsure how the seals go together. I have all
> the
> its from Bill Boulton, and his instruction sheet. But after looking
> closely
> t all the photos of installed hardtops I could find, it seems that they
> iffer from what I understand is the correct procedure. Most photos seem to
> how a seal resting on the rear cowl visible on the OUTSIDE of the Hardtop.
> he instructions seem to show the seals hidden on the inside of the hardtops
> luminum extrusion so that the seals would rest on the cowl with the
> extrusion
> itting around the cowl with no seals visible from the outside.
> If anyone has experience in installing new seals, I would appreciate your
> dvice before I start gluing.
>
> [demime 1.01d removed an attachment of type application/msword which had a
> name of Weather Seal Installation 3.doc]
> _______________________________________________
> Healeys@autox.team.net
> Donate: http://www.team.net/donate.html
> Suggested annual donation $12.75
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/healeys/pajtamuvek@gmail.com
_______________________________________________
Healeys@autox.team.net
Donate: http://www.team.net/donate.html
Suggested annual donation $12.75
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
|