fot
[Top] [All Lists]

[Healeys] Trunk Seal

Subject: [Healeys] Trunk Seal
From: josef-eckert at t-online.de (josef-eckert at t-online.de)
Date: Tue, 17 Jan 2017 21:38:34 +0100 (MET)
References: <1484646323975.4448354.4d4a0b38f185b0ce0962406affc9f453a3cd9a37@spica.telekom.de> <159adf0eb2f-7088-9d1e@webstg-a04.mail.aol.com>
Gary,
As regards aluminium boot lid seals there are at least two strong opinions:
 
One says there was no seal at all at the boot lid, but on the boot shroud 
opening. This might be only with very early 100s, but not confirmed.
 
The other which I share (for cars built at least from early 1954), as my 
car was fitted with the seal on the aluminium boot lid when I bought it 
unrestored.
On my car?s boot lid the seal starts and ends at the boot hinge support 
bracket on the left side of the boot lid.
 
To my wisdom on the steel lids it was glued in in two pieces and the ends 
to meet at the middle of both sides.
 
Josef Eckert
K?nigswinter/Germany
 
 
 
 
-----Original-Nachricht-----
Betreff: Re: [Healeys] Trunk Seal
Datum: 2017-01-17T20:39:31+0100
Von: "warthodson at aol.com" <warthodson at aol.com>
An: "josef-eckert at t-online.de" <josef-eckert at t-online.de>, 
"rrengineer.mike at att.net" <rrengineer.mike at att.net>, 
"Healeys at autox.team.net" <Healeys at autox.team.net>
 
 
 
That is an interesting bit of trivia!
I have an aluminum boot lid, but would like to know where the cut ends on 
both the alum & steel lids.
Gary Hodson

Where the cut ends up depends if it is a steel or aluminium boot lid.

 
 
 
-----Original Message-----
From: josef-eckert <josef-eckert at t-online.de>
To: Michael MacLean <rrengineer.mike at att.net>; Healeys, Forum 
<Healeys at autox.team.net>
Sent: Tue, Jan 17, 2017 12:56 pm
Subject: Re: [Healeys] Trunk Seal

Mike it is the correct seal for a 100 and the sharp edge goes to the 
outside. Where the cut ends up depends if it is a steel or aluminium boot 
lid.
 
Josef Eckert
K?nigswinter/Germany
 
 
 
-----Original-Nachricht-----
Betreff: [Healeys] Trunk Seal
Datum: 2017-01-17T03:22:22+0100
Von: "Michael MacLean" <rrengineer.mike at att.net
>
 
 
 
Is this the correct cross section for the 100 trunk seal.  Of course it is 
a Moss item I bought a few years ago.  Just getting around to addressing 
the trunk area.  Which side goes towards the inside of the trunk?  All the 
way around in one piece? Where is the cut ends end up?
Mike MacLean
 
_______________________________________________
<http://www.team.net/donate.html>
Archive: http://www.team.net/archive <http://www.team.net/archive>

http://autox.team.net/mailman/listinfo/healeys
<http://autox.team.net/mailman/listinfo/healeys>

http://autox.team.net/mailman/options/healeys/warthodson at aol.com
<http://autox.team.net/mailman/options/healeys/warthodson at aol.com>
?
-------------- next part --------------
An HTML attachment was scrubbed...
URL: 
<http://autox.team.net/pipermail/healeys/attachments/20170117/e3de8c47/attachment.html>

<Prev in Thread] Current Thread [Next in Thread>