Hi Les,
I may be "preaching to the converted " here but...
In order to determine which spring(s) are at fault it is necessary to test the
ride height of each end of the car in isolation to prevent a problem at one end
affecting the other.
To do this for the front, on a flat surface, jack the center of the diff (under
the drain plug), remove the rear wheels then lower the rear to normal ride
height. This produces a 3 point support.
Bounce the front a couple of times to ensure that the front suspension units
are operating correctly then measure the ride height both between the frame
rails and the ground and the tops of the front fender arches and the ground.
Repeat for the rear using a piece of pipe placed axially under the front cross
member.
In my experience it usually the rear springs that are at fault.
Michael S
BN1 #174
On Sat, Jan 14, 2017 at 10:03 AM -0500, "Bob Haskell" <rchaskell at
earthlink.net> wrote:
Jon & Les,
Installed height of the springs the same?
Were the front A arm inboard mounting bolts tightened with the car
sitting flat on the ground (normal ride height)?
How's the back of the car? It's not pitching the right front nose
downward, right?
Cheers,
Bob Haskell
AHCA 3000 MkI registrar
http://www.ciahc.org/registry_3000mk1.php
On 01/14/2017 07:15 AM, John Sims wrote:
> Can one of you help this person with his problem? Thanks
>
> John Sims
>
> *From:*Les Mathieson [mailto:mathlynn at bigpond.net.au]
> *Sent:* Friday, January 13, 2017 6:50 PM
> *To:* john at healey6.com
> *Subject:* BN4 - 100/6 front suspension
>
> Hi John,
>
> My name is Les Mathieson, from Paynesville in Australia,
>
> I own an 100/6, pictured.
>
> You have a great site, just wondering if you could give me some advice.
>
> My car has a ride height in the front, basically the right hand side of
> the body is about 50mm or 2 inches lower than the right hand side.
>
> We have checked most things and nothing was apparent.
>
> Therefore we suspected one of the Coil springs in the front are the
> issue. I have them out & we sent them to a pretty reputable spring maker
> for testing etc before we bought a new set.
>
> Unfortunately the tests showed they were both ok?
>
> We are waiting for them to be returned to re-assemble & look for other
> causes of the issue.
>
> Do you have any clues, insights or comments that might assist?
>
> Thanks
>
> Les
>
> Les Mathieson
>
> 4 Araluen Court
>
> (PO Box 142)
>
> Paynesville
>
> VIC 3880
>
> 0418106725
>
>
>
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation $12.75
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
>
> Healeys at autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
>
> Unsubscribe/Manage: http://autox.team.net/mailman/options/healeys/rchaskell
> at earthlink.net
>
_______________________________________________
Archive: http://www.team.net/archive
Healeys at autox.team.net
http://autox.team.net/mailman/listinfo/healeys
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://autox.team.net/pipermail/healeys/attachments/20170114/b81d1318/attachment.html>
|