--===============5655654860730432256==
boundary="----=_Part_2637021_22881737.1447187319077"
------=_Part_2637021_22881737.1447187319077
Content-Transfer-Encoding: quoted-printable
Don't forget to lift the lever up, before shifting into reverse. Many folks=
tend to force the gear lever over to the right (hitting it hard with the b=
ack of your hand), then down, without lifting.=C2=A0 This causes undue wear=
on the shift fork shaft.=C2=A0 There is an intentional 'lock out' in the d=
esign of the shaft, which is designed to prevent shifting into reverse when=
you really wanted a forward gear. Constant shifting into reverse without l=
ifting the lever will gradually wear down the shift fork shaft so that this=
'lock out' feature will no longer be functional.=C2=A0 This will then caus=
e more unintentional shifting into reverse when the car is moving forward, =
and resultant damage to the reverse gear.
A case in point.=C2=A0 Years ago, I went to look at a TR-4 that was for sal=
e, and was going to take it for a test drive. I had to back out of the spac=
e where it was parked.=C2=A0 We got in the car (me in the driver's seat, se=
ller in the passenger seat), and he instructed me to hit the left side of t=
he shift lever with the right side of my hand, as hard as I could.=C2=A0 He=
explained that this would move the lever over far enough that I could then=
pull it down into reverse.=C2=A0 He told me this was the way it was suppos=
ed to work.=C2=A0 Obviously, no one had instructed him on the correct proce=
dure.=C2=A0 Over the years, I've taken apart a number of gear boxes, and al=
most all of them have excessive wear on the reverse gear shift fork shaft, =
most to the point where there is virtually no 'lock out' affect remaining.
Just FYI
Jack
=20
From: "rkramer3@austin.rr.com" <rkramer3@austin.rr.com>
To: "FOT@autox.team.net FOT@autox.team.net" <FOT@autox.team.net>; Todd Red=
mond <alfetta95@optonline.net>=20
Sent: Tuesday, November 10, 2015 12:55 PM
Subject: Re: [Fot] Shift Knob
=20
I suspect the only thing about that shift know that is Triumph are the thre=
ads that allowed it to be spun onto the shifter. Reverse is to the bottom r=
ight, not left as shown, and it is 1st on the top left pull down for 2nd, u=
p and over for third, then down for fourth. Pop it over further to the righ=
t and pull down and you'll find reverse.
Bob Kramer
rkramer3@austin.rr.com
---- Todd Redmond <alfetta95@optonline.net> wrote:=20
> Can anyone identify this shift knob? =C2=A0The thumb switch is broken off=
but=20
> was in place between the H and L for overdrive. =C2=A0I'd like to replace=
it=20
> with the same. =C2=A0Kinda thinking its from a Dolomite.
>=20
>=20
> And since I've never driven this car, is that the location for reverse=20
> on a TR3 gearbox?
>=20
>=20
> Thanks
> Todd
>=20
_______________________________________________
fot@autox.team.net
http://www.fot-racing.com
Archive: http://www.team.net/archive
yahoo.com
------=_Part_2637021_22881737.1447187319077
Content-Transfer-Encoding: quoted-printable
<html><head></head><body><div style=3D"color:#000; background-color:#fff; f=
ont-family:HelveticaNeue, Helvetica Neue, Helvetica, Arial, Lucida Grande, =
sans-serif;font-size:16px"><div id=3D"yui_3_16_0_1_1447162486441_23118">Don=
't forget to lift the lever up, before shifting into reverse. Many folks te=
nd to force the gear lever over to the right (hitting it hard with the back=
of your hand), then down, without lifting. This causes undue wear on=
the shift fork shaft. There is an intentional 'lock out' in the desi=
gn of the shaft, which is designed to prevent shifting into reverse when yo=
u really wanted a forward gear. Constant shifting into reverse without lift=
ing the lever will gradually wear down the shift fork shaft so that this 'l=
ock out' feature will no longer be functional. This will then cause m=
ore unintentional shifting into reverse when the car is moving forward, and=
resultant damage to the reverse gear.<br></div><div id=3D"yui_3_16_0_1_144=
7162486441_23119"><br></div><div id=3D"yui_3_16_0_1_1447162486441_23120">A =
case in point. Years ago, I went to look at a TR-4 that was for sale,=
and was going to take it for a test drive. I had to back out of the space =
where it was parked. We got in the car (me in the driver's seat, sell=
er in the passenger seat), and he instructed me to hit the left side of the=
shift lever with the right side of my hand, as hard as I could. He e=
xplained that this would move the lever over far enough that I could then p=
ull it down into reverse. He told me this was the way it was supposed=
to work. Obviously, no one had instructed him on the correct procedu=
re. Over the years, I've taken apart a number of gear boxes, and almo=
st all of them have excessive wear on the reverse gear shift fork shaft, mo=
st to the point where there is virtually no 'lock out' affect remaining.</d=
iv><div id=3D"yui_3_16_0_1_1447162486441_23242"><br></div><div id=3D"yui_3_=
16_0_1_1447162486441_23148">Just FYI</div><div id=3D"yui_3_16_0_1_144716248=
6441_23241"><br></div><div id=3D"yui_3_16_0_1_1447162486441_23240">Jack<br>=
</div><div id=3D"yui_3_16_0_1_1447162486441_22203"><span></span></div><br>=
<div id=3D"yui_3_16_0_1_1447162486441_23151" style=3D"font-family: Helvet=
icaNeue, Helvetica Neue, Helvetica, Arial, Lucida Grande, sans-serif; font-=
size: 16px;"> <div id=3D"yui_3_16_0_1_1447162486441_23150" style=3D"font-fa=
mily: HelveticaNeue, Helvetica Neue, Helvetica, Arial, Lucida Grande, sans-=
serif; font-size: 16px;"> <div id=3D"yui_3_16_0_1_1447162486441_23149" dir=
=3D"ltr"> <hr id=3D"yui_3_16_0_1_1447162486441_23234" size=3D"1"> <font id=
=3D"yui_3_16_0_1_1447162486441_23233" size=3D"2" face=3D"Arial"> <b><span s=
tyle=3D"font-weight:bold;">From:</span></b> "rkramer3@austin.rr.com" <rk=
ramer3@austin.rr.com><br> <b><span style=3D"font-weight: bold;">To:</spa=
n></b> "FOT@autox.team.net FOT@autox.team.net" <FOT@autox.team.net>; =
Todd Redmond <alfetta95@optonline.net> <br> <b><span style=3D"font-we=
ight: bold;">Sent:</span></b> Tuesday, November 10, 2015 12:55 PM<br> <b><s=
pan style=3D"font-weight: bold;">Subject:</span></b> Re: [Fot] Shift Knob<b=
r> </font> </div> <div id=3D"yui_3_16_0_1_1447162486441_23155" class=3D"y_m=
sg_container"><br>I suspect the only thing about that shift know that is Tr=
iumph are the threads that allowed it to be spun onto the shifter. Reverse =
is to the bottom right, not left as shown, and it is 1st on the top left pu=
ll down for 2nd, up and over for third, then down for fourth. Pop it over f=
urther to the right and pull down and you'll find reverse.<br clear=3D"none=
"><br clear=3D"none">Bob Kramer<br clear=3D"none"><a shape=3D"rect" ymailto=
=3D"mailto:rkramer3@austin.rr.com"; href=3D"mailto:rkramer3@austin.rr.com";>r=
kramer3@austin.rr.com</a><br clear=3D"none"><div class=3D"qtdSeparateBR"><b=
r><br></div><div class=3D"yqt5649243518" id=3D"yqtfd60073"><br clear=3D"non=
e">---- Todd Redmond <<a shape=3D"rect" ymailto=3D"mailto:alfetta95@opto=
nline.net" href=3D"mailto:alfetta95@optonline.net";>alfetta95@optonline.net<=
/a>> wrote: <br clear=3D"none">> Can anyone identify this shift knob?=
The thumb switch is broken off but <br clear=3D"none">> was in pl=
ace between the H and L for overdrive. I'd like to replace it <br cle=
ar=3D"none">> with the same. Kinda thinking its from a Dolomite.<b=
r clear=3D"none">> <br clear=3D"none">> <br clear=3D"none">> And s=
ince I've never driven this car, is that the location for reverse <br clear=
=3D"none">> on a TR3 gearbox?<br clear=3D"none">> <br clear=3D"none">=
> <br clear=3D"none">> Thanks<br clear=3D"none">> Todd<br clear=3D=
"none">> <br clear=3D"none"><br clear=3D"none">_________________________=
______________________<br clear=3D"none"><a shape=3D"rect" ymailto=3D"mailt=
o:fot@autox.team.net" href=3D"mailto:fot@autox.team.net";>fot@autox.team.net=
</a><br clear=3D"none"><br clear=3D"none"><a shape=3D"rect" href=3D"http://=
www.fot-racing.com/" target=3D"_blank">http://www.fot-racing.com</a><br cle=
ar=3D"none"><br clear=3D"none">Donate: <a shape=3D"rect" href=3D"http://www=
.team.net/donate.html" target=3D"_blank">http://www.team.net/donate.html</a=
><br clear=3D"none">Archive: <a shape=3D"rect" href=3D"http://www.team.net/=
archive" target=3D"_blank">http://www.team.net/archive</a><br clear=3D"none=
">Forums: <a shape=3D"rect" href=3D"http://www.team.net/forums"; target=3D"_=
blank">http://www.team.net/forums</a><br clear=3D"none">Unsubscribe/Manage:=
<a shape=3D"rect" href=3D"http://autox.team.net/mailman/options/fot/jwheel=
er1947@yahoo.com" target=3D"_blank">http://autox.team.net/mailman/options/f=
ot/jwheeler1947@yahoo.com</a><br clear=3D"none"><br clear=3D"none"><br clea=
r=3D"none"></div><br><br></div> </div> </div> </div></body></html>
------=_Part_2637021_22881737.1447187319077--
--===============5655654860730432256==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
fot@autox.team.net
http://www.fot-racing.com
Archive: http://www.team.net/archive
--===============5655654860730432256==--
|