The tubeular pushrods are produced with an insert ball and cup that has a
portion that goes up into the tube. This is NOT welded in place but simply
pressed in. SO.......you can pull out the insert and shorten the pushrod as
you need then just press the insert back into place. I generally did this in a
lathe using a parting tool and therefore did not have to remove the insert I
just tooled off a bit of meterial right up next to the insert joint, tested it
for length and then went on as needed, recording as you go and then make all
the rest the same length. It's just not a big deal. ----- Original Message
-----
From: GuyotLeonF@aol.com
To: kaskas@earthlink.net ; FOT
Sent: Sunday, December 02, 2001 2:37 PM
Subject: Re: 6 cylinder pushrod length required
In a message dated 02/12/01 19:41:57 GMT Standard Time, kaskas@earthlink.net
writes:
Subj:Re: 6 cylinder pushrod length required
Date:02/12/01 19:41:57 GMT Standard Time
From: kaskas@earthlink.net (Kas Kastner)
To: GuyotLeonF@aol.com
The length is also effected by the base circle diameter of the camshaft.
If
you have a re-ground cam the rod will come out shorter due to the
reduction
of the base circle of the cam. Cams, even stock, can have a very different
base circle diameter so a known length dosen't mean it will be what you
want.
----- Original Message -----
From: "Rob Dardano" <19to1tr6@mediaone.net>
To: <GuyotLeonF@aol.com>; "FOT" <fot@autox.team.net>
Sent: Sunday, December 02, 2001 9:05 AM
Subject: Re: 6 cylinder pushrod length required
> Leon your push rod lenght will be determind buy your rocker geomitry If
the
> head has been modified the stock rods could be a little long The tip
of
> the rocker should ride on the center of the valve stem, I hope other
> members will correct me or perhaps state it correctly rob
> ----- Original Message -----
> From: <GuyotLeonF@aol.com>
> To: "FOT" <fot@autox.team.net>
> Sent: Sunday, December 02, 2001 9:08 AM
> Subject: 6 cylinder pushrod length required>
>
> > Friends,
> >
> > I require the length of an engine pushrod:
> >
> > It is part # 151073 as found in the Vitesse Mk.2 engine, also the
GT6-2,
> and
> > GT6-3 [up to KE/KF10000].
> >
> > but NOT part # 129058 from the Vitesse 6, 2-Litre Mk.1 or GT6-1.
> >
> > nor part # 149513 from GT6-3 [from KE/KF10001], Triumph 2000 Mk.2,
TR6
> [all
> > CP models]
> > (this one is 20.6 cm, or 8.11" long, to the end of the 'ball').
> >
> > nor part # 148916 from TR6 [all CR models]
> > (this one is 21.1 cm 8.30" long).
> >
> > Could anyone please confirm the length of 151073 ?
> >
> > Thank you in advance
> >
> > Leon
Rob, Kas, Thanking you both for your responses,
Further to the above, the reason that I need to know the length of 151073 is
because I presently have fitted to my Vitesse Mk.2/GT6+ engine, a Holbay
camshaft of "Inlet 37/67 exhaust 73/31", this has worked, and continues to
work very well indeed for the last 9,000+ miles, with a slightly raised
compression ratio, (only about half a ratio), and the rocker gear presently
comprising an OE Triumph shaft of the correct hardness, lightened and balanced
rocker arms with the oilways slightly opened up, and bushed with oilite
phosphor bronze...and taking the cam lift via standard pushrods 151073.
I have obtained from Ted Schumacher a set of Roller Rockers, (as original
1.5 ratio), which I intend to fit to my present rocker shaft, along with the
solid spacers that I currently have fitted instead of spacer springs, (long
gone).
At the same time, I think it would be a good idea if I replace the original
151073 pushrods with tubular chrome moly pushrods of the correct length for
ultimate reliability at high rpm.
However, I need to order the correct pushrods and have them in my possession
before I take down the top of my engine to do the neccessary work, and all I
have in my possession at the moment is one set of 149513 pushrods from a TR6
(CP), which measure 8.11" and one set of chrome moly pushrods (on loan), which
measure 8.3" (suitable for a TR6 (CR)).
Therefore, I still do not know the length of the 151073 pushrods presently
working perfectly well in my engine!
I know that since I am not altering the camshaft from the present spec, nor
am I removing the cylinder head, and the roller rockers are 1.5 ratio, just
like those presently fitted, I would be well advised to fit chrome moly
tubular pushrods of the exact same length also.
Does that make sense?
Regards
LC)on
1921 French Grand Prix driver: Albert Guyot, to Ernest Ballot ,
"Therebs only one winner in any race: the man who gets home first."
1963 Triumph Vitesse 2-Litre Convertible (Diva)
1988 Volkswagen 1600GT Scirroco Coupe (Driver)
Wimbledon, London, England.
|