Re: [6pack] Throttle Linkage ?S? Connectors

[Tomislav Marincic <tomislav.marincic@earthlink.net>]

Hello Robert,
 
I'll snap you a photo of the barrel linkage in place. One of them works, but if 
I recall correctly, there was no way to use two and get them installed without 
removing the carbs and linkage.
 
I Jet Hot coated both of my manifolds, and wrapped the exhaust header in 
Thermo-Tec exhaust tape. The Jet Hot keeps the manifolds looking nice, and 
keeps the header from corroding, but it won't cure your fuel cook-off problems. 
Your best bet is one of Joe Alexander's heat shields, which I think are being 
sold through Moss as well. 
https://mossmotors.com/aluminum-heat-shield-by-a-r-e-for-zenith-stromberg-carbs?utm_source=feed&utm_medium=free&utm_campaign=shopping&gclid=EAIaIQobChMI4v7154Cx9AIVhcqGCh0tWAy8EAQYAiABEgKXSPD_BwE
 
(https://mossmotors.com/aluminum-heat-shield-by-a-r-e-for-zenith-stromberg-carbs?utm_source=feed&utm_medium=free&utm_campaign=shopping&gclid=EAIaIQobChMI4v7154Cx9AIVhcqGCh0tWAy8EAQYAiABEgKXSPD_BwE)
 
https://www.summitracing.com/parts/the-11021?rrec=true 
(https://www.summitracing.com/parts/the-11021?rrec=true)
 
Good Luck, Tom
 
 
 
 
-----Original Message-----
From: robert rudolphi 
Sent: Nov 23, 2021 1:23 PM
To: 6pack@autox.team.net , Tomislav Marincic 
Subject: Re: [6pack] Throttle Linkage ?S? Connectors
 
To follow up on this I am having my carbs rebuilt this winter (Joe Curto) and 
was thinking about have the intake and stock exhaust manifolds Jet coated. I am 
trying to reduce hard starting when hot. Would also like to get the throttle 
linkages re-plated/refinished and was wondering what is the best way to go?
 
Thanks in advance for any feedback
 
Robert
 
 
 
 
 
On Tuesday, November 23, 2021, 12:13:49 PM EST, Tomislav Marincic wrote:
 
 
 
 
 
 
When I set up my dual ZS175â??s I used new link clips from Roadster Factory. 
They quickly became distorted and introduced slop into the linkage.
 
Iâ??m currently using one SU link clip sourced from Richard Good, which is much 
sturdier and more rust-resistant than the ZS part. Iâ??m also using a single 
rigid coupling that I sourced from Grainger. I forget why, but installing two 
shaft linkages was problematic, and the gap between carb throttle shafts was 
too wide to use two SU linkages.
 
I might have one of each in my spares if you need them.
 
https://www.grainger.com/search?searchQuery=nomar+clx-5-5-a&searchBar=true
 
https://www.goodparts.com/product/folded-coupler-carb-shaft/
 
Pix on requestâ?¦Tom
 
 
 
_______________________________________________
Support Team.Net http://www.team.net/donate.html
Suggested annual donation  $12.96
Archive: http://www.team.net/archive
 
 
6pack@autox.team.net
http://autox.team.net/mailman/listinfo/6pack
 
Unsubscribe/Manage: 
http://autox.team.net/mailman/options/6pack/robertrudolphi@yahoo.com
 

 
_______________________________________________
Support Team.Net http://www.team.net/donate.html
Suggested annual donation  $12.96
Archive: http://www.team.net/archive


6pack@autox.team.net
http://autox.team.net/mailman/listinfo/6pack

Unsubscribe/Manage: 
http://autox.team.net/mailman/options/6pack/mharc@autox.team.net