6pack
[Top] [All Lists]

[6pack] Fw: [TR] TR-3/4/5/6 Aluminum hubs Commercial message

To: "6 pack" <6pack@autox.team.net>
Subject: [6pack] Fw: [TR] TR-3/4/5/6 Aluminum hubs Commercial message
From: "Bob Danielson" <75tr6@tr6.danielsonfamily.org>
Date: Tue, 12 Oct 2010 09:10:55 -0400
I don't think Tony posts to 6-Pack so I'm forwarding his email (shown below) 
to this group. Contact Tony and not me ;-)

Bob

Bob Danielson
1975 TR6 CF38503U
Running w/ Throttle Body Injection,
Toyota 5 speed & Nissan LSD
http://tr6.danielsonfamily.org

--------------------------------------------------
From: "Tony Drews" <tony@tonydrews.com>
Sent: Tuesday, October 12, 2010 12:53 AM
To: <triumphs@autox.team.net>
Subject: [TR] TR-3/4/5/6 Aluminum hubs Commercial message

> uncle jack's racing Aluminum front hubs are going back into production for 
> a limited quantity run.
>
> These are a revised design that I've been testing on my TR-4 race car all 
> season.  We are using a different set of inner bearings than the prior 
> aluminum hubs used, but they have the same high load rating and are about 
> half of the cost.  These hubs eliminate a significant weakness in the 
> stock hubs between the inner and outer flange.  They incorporate very high 
> load rating, larger than stock Timken bearings which eliminates the 
> bearing failure issues that are present with stock bearings when using 
> sticky tires.  I have been running set with bearings of this load rating 
> from 2003 through 2009 (before running the prototypes this year) and can 
> detect no wear in the bearings.  I drive them HARD, and am not afraid to 
> use the curbs.
>
> I'm taking pre-orders at this time - no deposits yet.  But, please don't 
> pre-order a set if you don't really intend to buy them.  This is a very 
> significant investment for me, and I need to gauge the level of interest.
>
> Here's how the pricing shakes out (US dollars):
> A) Bare hubs: $175.00 each / $350.00 per pair
> B) Hubs with Timken races and ARP studs installed: $280.00 each / $560.00 
> per pair
> C) Hubs with all bearings, seals, dust caps and ARP studs installed: 
> $370.00 each / $740.00 per pair
>
> For folks who order these hubs, if you already have the heavy duty axle 
> kit, I'll supply a pair of bearing spacers that will work with these hubs 
> for $40 per pair.
>
> If you don't already have a set of the Heavy Duty front axles, I'll supply 
> the axle kit along with the hubs for $150 per pair.  These are the lowest 
> prices for the axle kits that have been offered.
>
> Shipping is a flat $20 in the continental US, $35 to Canada, and other 
> international shipping is probably $50 - at least to Germany or to 
> Australia.
>
> The hubs are designed to accept ARP 1/2" x 3" studs, but ARP 7/16" x 3.2" 
> studs can be specified.  7/16" is the stock diameter.
>
> If you're interested, please send an e-mail to tony@tonydrews.com with the 
> following info:
> *  Which set you're interested in (A, B or C)
> *  How many hubs are desired (2 would be assumed)
> *  Stud diameter desired
> *  Are spacers needed?
>
> Thanks for your interest,
> Tony Drews
> tony@tonydrews.com
> uncle jack's racing
_______________________________________________

6pack@autox.team.net
Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums

<Prev in Thread] Current Thread [Next in Thread>
  • [6pack] Fw: [TR] TR-3/4/5/6 Aluminum hubs Commercial message, Bob Danielson <=